A garbage disposal that hums and will not turn is usually jammed, and the fix is often a reset button and a hex key. A disposal that leaks, trips the breaker, drains slowly into the sink or needs to be replaced is a job for a plumber, and an electrician may be needed if the wiring is wrong. Tell the plumbing business what you hear and see and what brand you have. For other drain problems, start from the home page or ask for quotes below.
What can you check before you call a plumber?
Turn the disposal off at the wall switch, then look for something stuck, press the red reset button on the bottom, and try again. The manufacturer's manuals say to switch the power off before clearing a jam, to use a hex wrench in the socket under the unit to free the blades and never to put your hand in the chamber.
Steps that are usually safe:
- Switch the disposal off, and unplug it or turn off its breaker if you can reach it.
- Use tongs or pliers, not your fingers, to remove anything you can see.
- Insert the hex key that came with the unit (often a quarter-inch size) into the socket at the bottom center and work it back and forth until the blades turn freely.
- Press the reset button, restore power, run cold water and test.
If the disposal still hums, trips the breaker again, smells burnt or leaks from the body, stop using it. A leak from the bottom or the side usually means the unit has failed internally, and the answer is replacement, not a repair.
What do plumbers say about garbage disposals?
Plumbers generally advise running cold water with the disposal, grinding small amounts of soft food waste at a time and keeping grease, fibrous peels, large bones, pits and non-food items out. Manufacturers say the same: cold water helps move waste and keeps grease firm, and the water should run for several seconds after grinding.
Grease, coffee grounds and starchy food in bulk often cause the drain clogs plumbers see, not the disposal itself. A disposal grinds food, but the drain downstream is the usual trouble spot. If sink water backs up when the disposal runs, the problem may be the drain line, and a drain cleaning company or plumber can clear it.
Check your model's manual for what it can grind. Different models, including quieter ones, publish different lists for hard items.
Is it okay to pour boiling water down your garbage disposal?
No. Manufacturers say to use cold water when running a disposal, and they list extremely hot water among things to avoid. Hot water can melt grease, which then settles farther down the drain and hardens. Flush with cold water after grinding.
If a grease clog is already forming, a plumber can clear it with a cable or a jet. See also hydro jetting cost if the whole line is slow.
What does a disposal installation or replacement involve?
The plumber removes the old unit, cleans the sink flange, fits the new mounting assembly, connects the drain, hooks up the dishwasher hose if there is one, and connects power. Installation is quicker when you swap a like-for-like unit and takes longer when there is no existing disposal, a drain change or new wiring.
Details a plumber checks:
- Mount type: many brands use a quick-lock mount, and adapters can fit a different brand's flange.
- Drain position and trap arrangement under the sink.
- Dishwasher connection: if a dishwasher drains into the unit, the knockout plug inside the disposal inlet must be removed so the hose can drain. Manuals show the step; forgetting it is a common cause of a dishwasher that fills with water.
- Power: a plug-in cord or a hardwired connection.
- A switch location that works with the unit.
The easiest unit to install is generally the one that matches your existing mount and electrical setup. Manufacturers publish diagrams, and the Moen and InSinkErator instruction sheets show the parts and the order of assembly.
Can I hardwire a corded garbage disposal?
Some models come with a power cord and others are hardwired, and manufacturers sell adapters so one unit can be wired either way. Wiring is electrical work, and a mistake can be dangerous, so follow the maker's manual and local code. If you are unsure of the circuit, call a plumber or an electrician.
California separates trades by license class. Plumbing contractors cover the plumbing side of the install; the electrical side falls under electrical contractors (C-10). A plumbing business may bring an electrician, or you may be asked to arrange one. Ask before the visit so nothing is held up. Some disposals need a switch or an outlet under the sink, and adding one is more than a swap.
What should you ask in a quote for disposal work?
Ask whether the price covers the unit, mount, drain parts, power connection and removal of the old disposal. Ask who handles the dishwasher hookup, whether a new switch or outlet is needed and what warranty comes with the unit and the labor. A written quote lists these, and the plumber confirms the price after seeing the sink cabinet.
Prices depend on the unit's horsepower and features, whether you supply the disposal, the wiring and whether the drain needs changes. The garbage disposal cost page explains how those add up. For leaks under the sink beyond the disposal, see pipe burst under sink. For the general visit process, see plumber service and plumber cost. When you are ready, request quotes from local plumbing businesses.
